product_image

MYK LATICRETE PUA 212

ADHESIVES by MYK LATICRETE

 PUA 212 is a two component, modified Polyurethane Adhesive designed for the installation of ceramic tile, vitrified tile, metal tile, glass tile, agglomerates, glass mosaic tile and natural stone on any substrate. It is highly elastic, thixotropic and suitable to lay water sensitive tiles & stones on highly expandable, deformable, absorbent and non-absorbent substrates.

Areas of Application:- Designed especially for interior and exterior floor and wall installations of all types of ceramic tile, vitreous, semi-vitreous tile, glass mosaic tiles, precast terrazzo, engineered stone, metal tiles and natural stones over concrete and on a variety of substrates including metal substrates and drywall boards  

Unit

4kg & 8kg

Price / Unit

₹2630.00
Excludes GST*
Get a quote from our Authorized Dealer "ShubhTiles" (Vile Parle, Mumbai)
Get Quote

Application

  1. Tile/Stone, Mesh Backed GMT & Agglomerates: Apply adhesive to the substrate with the flat side of the trowel, pressing firmly to work into surface. Comb on additional adhesive with the notched side. Use the proper sized notched trowel to ensure full bedding of the tile. Spread as much adhesive as can be covered with tile in 10 minutes. Back butter large format tiles (> 12”x12”) to provide full bedding and firm support. Place tiles into wet, sticky adhesive and beat in using a beating block and rubber mallet to imbed tile and adjust level. Check adhesive for complete coverage by periodically removing a tile and inspecting bedding adhesive transfer onto back of tile. If adhesive is skinned over (not sticky), remove and replace with fresh adhesive.
  2. Glass Mosaic tiles – Paper faced: The PUA 212 adhesive shall be applied to the surface to be tiled with a notched trowel using a scraping motion to work the adhesive into good contact with the surface to be covered. Notch trowel with notches approximately 4mm is recommended to get a bed thickness of 1.5-2mm. V-notch of 3mm also can be used to get bed thickness of 1.5mm. Apply only so much that can be covered with tile within 10-15 minutes or while the adhesive surface is still tacky. The Glass Mosaic tiles shall then be set in place and beaten gently with mallet or grouting float to insure 100% full bedding. Tiles shall be aligned to achieve uniform joints and then allowed to set until firm. Excess adhesive must be cleaned from the surface of the tile with a wet cloth or sponge while the adhesive is fresh and has not hardened. After the tiles are set firm, the face of the sheets of front mounted glass mosaic tiles shall then be dampened and the face mount paper can be removed.
Watch Video

Substrate

  • Concrete – VDF, Tremix and MIVON
  • Concrete masonry & brick masonry
  • Cement mortar beds & plaster
  • Metal floors and walls
  • Tile and stone
  • Wood & plywood*
  • Cement backer board*
  • Cement terrazzo
  • Engineered stones & marbles
  • Epoxy or PU resin based substrates
  • Gypsum board*
  • Existing ceramic tile
  • Rubber, PVC and linoleum substrates
  • *Consult the backer board manufacturer’s data sheet for the specific recommendations and load bearing capacity of specific board intended for use.

Coverage

1.5 to 2.1 sft per 1 kg with a 1/4” x 1/4” (6mm x 6mm) square notch trowel for bed of 3 mm. Coverage will vary depending on trowel notch size, type and size of tile and substrate smoothness and evenness.

Varies in accordance with the size and type of the tile and stone installed.

Example for a Bed Thickness of 3mm it will cover 18-20sqft per 8kg pail. (Approximate)

Technical Data Sheet
company logo
About Us Privacy Policy Terms & Conditions Contact Us

© 2020 DCONSTRO Copyright